Industrial Hygiene in Construction

I titled this post, “hazards of drywall”, but it encompassing most of the common hazards of plaster, mud, gypsum, wall-hangers, tapers, and acoustic employees.

1. Corrosive drywall.

   I have not dealt with this subject on a personal level. However, AIHA has a new guidance document titled, “Assessment and Remediation of Corrosive Drywall: An AIHA Guidance Document“, which is a clarification of an earlier white paper document from 2000, titled, “Corrosive Drywall“. The danger is from a specific type of drywall which was imported from China. After installation it is known to emit sulfide vapors, which corrode copper (electrical wires), and can give off a sulfur smell (HT to JeffH in Ohio).

2. Asbestos in mud/plaster.

   Be aware, some older buildings (pre 1980s) may have asbestos in the mud compound or plaster (not as common). This will be a concern if you are performing demo on these walls. Info here.

3. Silica (dust) in joint (mud) compound.

   Some types of silica I have found to have silica. This can be an issue when sanding. AND, if you install drywall like me…you do a lot of sanding. More information from an earlier post can be found here. NIOSH has some suggestions too.

4. Leaded sheetrock. If you are installing (or demo) leaded sheetrock, you NEED to protect yourself. Airborne levels of lead can approach the exposure limits, even during installation. More info here.
5. Lead in paint. If you’re tying into existing plaster/drywall and there’s paint, you need to know if there’s lead in it. Sanding on the paint is a good way to be exposed. More info here.
6. Ergonomics. Hanging the wallboard takes a toll on your body after 20 years (or less). Not to mention sanding. Washington OSHA (L&I) has a good demo.
7. Noise. Cutting steel studs, powder actuated tools (there’s lead exposure too, you know).
8. Skin hazards. Cutting, but also dermatitis from prolonged exposure to dust.
9. Eye hazards. Dust, carpentry, etc. Working overhead is an easy way to get falling items in your eyes.
10. Falls. Last on my list, but certainly not the least. Scaffolding, working from ladders, and using stilts, to name a few.

For better, or worse, the silica rule has been delayed, again. This delay is for an extension of the public comment period, which goes until December 12, 2013. Public hearings are set to begin on March 4, 2014.

Find OSHA here, with links to my previous post. A NPR story from February, 2013.

My views on this rule haven’t changed much: It’s still a mixed-bag. There are still overexposures to silica (see my pictures from the last 3 weeks). However, will the new rule change the behavior?

• Overexposures are still happening
• Silica deaths have decreased over the past (without the new rule)
• Will the small employers (the ones who typically offend the most) comply? Or just wait to be cited?

But, my overwhelming thought is this:

• Any new rule will generate “noise” for the subject of silica. And, that’s a good-thing.
• This will drive:
  • compliance
  • changes
  • innovation
  • discussions
  • awareness

I previously wrote about a worst-case scenario in which asbestos was not discovered till after it was disturbed.

Recently I heard a story of the opposite:

A general contractor hired a company to remove various pieces of asbestos. They had obtained an asbestos building survey, which clearly stated where the  asbestos was located. A boiler with surrounding insulation was identified as non-asbestos containing (asbestos-free). The employee was using a bobcat to demolish the boiler. As he started to tear into the insulation surrounding the boiler (disturb it), he paused. He checked the building survey again, and it had clearly stated it was “asbestos free” (actually 5 samples had been taken of the insulation around the boiler). Then, he did what most other people would not do: HE REFUSED to demo the insulation. He told the General Contractor and owner he thought it was asbestos containing and wanted it tested, AGAIN.

Guess what they found? Yep. Asbestos WAS contained inside the insulation around the boiler.

There was obviously some break-down in communication with the report, inspector, and possibly the lab.  However, this employee is to be commended and, really, the safety culture at this company should be congratulated. You never know where you will find asbestos.  The employee had enough guts to speak up for his safety (and for the others).

Measuring good-safety behavior is the type of thing we should reward. In the past (and still today) many safety-people measure losses ( ie. how many injuries). This is backwards thinking. We should be rewarding good behavior and encouraging people to speak up for safety.

For example; what do you say to this guy?

If you live in the United States, you have less than one month to train your employees on the new Hazard Communication standard (1910.1200(h) & 1926.59), which should include information about the new types of Safety Data Sheets (formerly known as MSDS) and the adaptation with the Global Harmonization System (GHS). December 1, 2013 is the enforcement start date for OSHA. Don’t make this complicated, it is straightforward. Here’s what you should do:

• Train employees in hazard communication (simply: so they know the hazards they are working with)
• Document your training (in case of an OSHA inspection)
• Show them a sample Safety Data Sheet (SDS), compared with the old MSDS
  • Explain the new standard hazard phrasing & pictograms
  • Explain how to review a SDS
  • Remind them about container labeling
• Explain that the new SDS will not be available immediately, but will roll-out over a few years (or more)

*Please note the “Beer” hazard warning on the right is not GHS compliant. 

For Help:

• Oregon OSHA (OR-OSHA has a new fact sheet on what you need to do for compliance.
• Here’s a link to a sample hazard communication plan (in Word!). More help here.
• AND, a free training guide for employers, another here. Shout-out to Siobhan & Dan at SAIF for this.
• Also, some Susan Harwood free training materials here (spanish too!).